This is the user guide for the SKMEI 2701, the round digital watch on a stainless-steel bracelet. If you lost the paper that came in the box, or the watch arrived without one, you will find everything here.
Good to know: the 2701 is a new SKMEI model, and SKMEI has not published its printed leaflet online yet. The buttons, the display and the specs below come from SKMEI’s own drawings of this watch. The setting steps follow the official leaflets of SKMEI’s other four-button digital watches (LIGHT, START, MODE and RESET). If your watch does something different at any step, write to us and tell us what you see. We will help you right away.
The Four Buttons

- LIGHT (top left): turns on the backlight.
- START (top right): starts and stops the stopwatch and the countdown. On a setting screen it changes the number that is flashing.
- MODE (bottom left): moves from one mode to the next. On a setting screen it moves to the next item.
- RESET (bottom right): hold it to open the setting of the screen you are on, and press it to finish. It also resets the stopwatch.
Reading the Display
| On the screen | What it means |
|---|---|
| SA 10-20 (top line) | Day of the week (SA = Saturday) and the date (month and day) |
| Big digits | Hour and minutes |
| P | Afternoon or evening (PM), in 12-hour format |
| Small digits (bottom) | Seconds |
| Bell | The daily alarm is on |
| ))) SNZ | The hourly chime or snooze is on |
The days are shown in English, with two letters: MO, TU, WE, TH, FR, SA and SU.
The Modes
The 2701 has five modes: time, stopwatch, countdown timer, alarm and second time zone (dual time). Each press of MODE takes you to the next one. The order can vary a little, so keep pressing MODE until you are back at the time.
Setting the Time and Date
- Press MODE until you are on the normal time screen.
- Hold RESET for about 3 seconds, until the seconds start to flash.
- Press START to reset the seconds to 00.
- Press MODE to move to the next item: hour, minutes, then the date (year, month, day) and 12/24h. The order can change a little; just follow what is flashing.
- While an item is flashing, press START to change it. Hold START to change it faster.
- When you are done, press RESET. If you do nothing for about a minute, the watch also saves and goes back to the time on its own.
If holding RESET does nothing: press MODE a few times. On some versions, the time setting is one of the screens in the MODE sequence: you will see a screen where the digits flash by themselves. There, RESET moves to the next item, START changes it and MODE finishes. If neither way works, contact us.
Tip: reset the seconds when your phone reaches a full minute. The day of the week usually follows the date by itself, so set the year and the date correctly.
12-Hour or 24-Hour Time
The 12/24h choice is one of the items in the time setting (see above). In 12-hour format, a P appears next to the hour in the afternoon and evening. Check it when you set the alarm, so it does not ring at 7 at night instead of 7 in the morning.
Second Time Zone (Dual Time)
- Press MODE until you reach the second time screen.
- Hold RESET until the hour flashes.
- Press START to change the hour. Press MODE to move to the minutes, if your version lets you change them.
- Press RESET to finish. The seconds follow the main time.
Setting the Alarm
- Press MODE until you reach the alarm screen.
- Hold RESET until the alarm hour flashes.
- Press START to change the hour. Press MODE to move to the minutes and change them with START.
- Press RESET to finish.
Alarm On/Off and Hourly Chime
- On the alarm screen, press START to switch between: alarm on (bell), hourly chime on ()))), both on, and both off.
- When the alarm rings, press any button to stop it.
- The marks stay on the screen in every mode, so you can always see if the alarm is set.
Stopwatch
- Press MODE until you reach the stopwatch.
- Press START to start and to stop.
- While it is running, press RESET to freeze a split time on the screen (it keeps counting). Press RESET again to go back.
- To reset it to zero, stop it with START, then press RESET.
Countdown Timer
- Press MODE until you reach the countdown screen.
- Hold RESET until the numbers flash. Use START to change them and MODE to move between hours, minutes and seconds. Press RESET to finish.
- Press START to start and stop the countdown.
- When it reaches zero, the watch beeps. Press any button to stop the sound.
The Backlight

Press LIGHT once, in any mode, and the whole screen glows for a few seconds. Using the light a lot makes the battery run out sooner, so there is no need to hold the button down.
Adjusting the Bracelet
The steel bracelet has removable links. To make it smaller, a watch shop can take out one or more links in a few minutes. Take the same number of links out of each side of the clasp, so the clasp stays centered under your wrist.
Water Resistance (3 Bar / 30 m)
Despite the “30 m”, this does not mean you can dive or swim with it. It means:
- OK: sweat, rain and splashes.
- Not OK: swimming, showering, the pool, the sea, washing hands under a strong tap, or hot water (sauna, hot tub).
- Never press the buttons when the watch is wet.
Battery and Care
- When the screen gets faint or the light gets weak, the battery is running low. Take it to a watch shop to change it: opening the back yourself can damage the rubber seal that keeps water out.
- Clean the case and the bracelet with a soft, damp cloth and dry them well. Do not use alcohol or other chemicals on the glass.
- Keep the watch away from strong heat (a car dashboard in the sun, for example) and from strong magnets.
- After a battery change, set the time and the date again.
If Something Looks Wrong
| What you see | What to do |
|---|---|
| Numbers keep flashing | The watch is in setting mode. Press RESET, or wait about a minute without touching anything. |
| The day of the week is wrong | Check the year and the date in the time setting. The day follows them. |
| The alarm did not ring | Check that the bell is on the screen and that the P (PM) mark is right in the alarm time. |
| The time is 12 hours off | In 12-hour format, check the P mark and set the hour again. |
| The screen is faint or blank | The battery is low. Take it to a watch shop for a new one. |
| Fog under the glass | Water got in. Stop using it in water and contact us. |
Specifications
| Item | SKMEI 2701 |
|---|---|
| Display | Digital |
| Case | Zinc alloy, 42.7 x 46.7 mm, 11 mm thick |
| Glass | Glass |
| Bracelet | Stainless steel, 19.6 mm wide, 220 mm total length, fold-over clasp |
| Weight | 100.4 g |
| Water resistance | 3 Bar (30 m) |
| Functions | Time, day, date, 12/24h, second time zone, alarm, hourly chime, stopwatch, countdown, EL backlight |
Need Help?
If something here does not match your watch, or you are stuck at any step, send us a message and tell us what the screen shows. A short video or photo helps a lot. You can also see the watch again on the SKMEI 2701 page.
